Router Bits

Filter By Category

46/91 x 1/4 TCT 90° Shank Mounted Template Profiler 12.7 x 9.5mm

46/91 x 1/4 TCT 90° Shank Mounted Template Profiler 12.7 x 9.5mm

Code: TRE469114TC
£45.88 Ex VAT
Profilers with shank mounted bearings for guidance, for use with router mounted above or below a table when following a template. Bearing guided cutters are suitable for both...
View Details
46/95 x 1/4 TCT 90° Shank Mounted Template Profiler 12.7 x 25.4mm

46/95 x 1/4 TCT 90° Shank Mounted Template Profiler 12.7 x 25.4mm

Code: TRE469514TC
£50.31 Ex VAT
Profilers with shank mounted bearings for guidance, for use with router mounted above or below a table when following a template. Bearing guided cutters are suitable for both...
View Details
4/70 x 1/2 TCT Two Flute Cutter 25.0 x 25mm

4/70 x 1/2 TCT Two Flute Cutter 25.0 x 25mm

Code: TRE47012TC
£62.37 Ex VAT
Two flute straight cutters produce a cleaner finish than the single flute cutters and are suitable for grooving, rebating, morticing and drilling. Use Tungsten Carbide toolin...
View Details
47/4 x 1/4 TCT Pierce & Trim Cutter 6.3 x 18mm

47/4 x 1/4 TCT Pierce & Trim Cutter 6.3 x 18mm

Code: TRE47414TC
£31.71 Ex VAT
Combination pierce and trim cutters. These cutters pierce and cut out aperture in laminate worktops. The base of the cutter acts as a guide follower. Single Flute cutters. S...
View Details
4/8 x 1/2 TCT Two Flute Cutter 25.4 x 25mm

4/8 x 1/2 TCT Two Flute Cutter 25.4 x 25mm

Code: TRE4812TC
£64.31 Ex VAT
Two flute straight cutters produce a cleaner finish than the single flute cutters and are suitable for grooving, rebating, morticing and drilling. Use Tungsten Carbide toolin...
View Details
50/05 x 8mm HSSE Helical Plunge Bit 5mm

50/05 x 8mm HSSE Helical Plunge Bit 5mm

Code: TRE50058HSE
£26.06 Ex VAT
Tooling for use on webbed aluminium and UPVC extrusions by window and door fabricators. Cutters are produced in special high speed steel (HSSE) to ensure a clean cut and resis...
View Details
50/06 x 8mm HSSE Helical Plunge Bit 6mm

50/06 x 8mm HSSE Helical Plunge Bit 6mm

Code: TRE50068HSE
£28.88 Ex VAT
Tooling for use on webbed aluminium and UPVC extrusions by window and door fabricators. Cutters are produced in special high speed steel (HSSE) to ensure a clean cut and resis...
View Details
50/08 x 8mm HSSE Helical Plunge Bit 8mm

50/08 x 8mm HSSE Helical Plunge Bit 8mm

Code: TRE50088HSE
£26.06 Ex VAT
Tooling for use on webbed aluminium and UPVC extrusions by window and door fabricators. Cutters are produced in special high speed steel (HSSE) to ensure a clean cut and resis...
View Details
50/19 x 8mm HSSE Steel Helical Plunge Bit 5mm

50/19 x 8mm HSSE Steel Helical Plunge Bit 5mm

Code: TRE50198HSE
£40.03 Ex VAT
Tooling for use on webbed aluminium and UPVC extrusions by window and door fabricators. Cutters are produced in special high speed steel (HSSE) to ensure a clean cut and resis...
View Details
50/51 x 8mm HSSE Helical Plunge Bit 8mm

50/51 x 8mm HSSE Helical Plunge Bit 8mm

Code: TRE50518HSE
£42.79 Ex VAT
Tooling for use on webbed aluminium and UPVC extrusions by window and door fabricators. Cutters are produced in special high speed steel (HSSE) to ensure a clean cut and resis...
View Details
5/1 x 1/4 TCT Hinge Recessor 12.7 x 19mm

5/1 x 1/4 TCT Hinge Recessor 12.7 x 19mm

Code: TRE5114TC
£35.44 Ex VAT
Two flute TC cutter giving good chip clearance. Ideal for shallow lateral routing cuts such as recessing hinges.Corners will require final trimming square with a hand chisel o...
View Details
B127 Replacement Bearing 1/2in Diameter 1/4in Bore

B127 Replacement Bearing 1/2in Diameter 1/4in Bore

Code: TREB127
£10.44 Ex VAT
Replacement bearing to suit all Trend bearing guided router cutters. The Bearings are shielded to prevent penetration of dust and grease packed for life and should not be cle...
View Details